Home > Xerox Workcentre > Xerox Workcentre Xd120f L6 Error

Xerox Workcentre Xd120f L6 Error

CH Status Code RAP (With SDF) The Main PWB sensed that the Toner Cartridge is not present or fully seated. Go to Flag 1 . Q> 5DE DCCF IWTEFLOCK S4 +5-TJT IMT t K SW. £ CNI1B +ivCn nn.K CRn — ii i ■ i- .-II I . . Actuate the Drum Cartridge Reset Switch. useful reference

Scoreboard Ratings See detailed Xerox customer service rankings, employee comments and much more from our sister site. There is approximately +22 VAC present. Y N Refer to Initial Actions/System Checks to begin your repair. Have a manual for Xerox WorkCentre XD120f Copier?

N.BI LL^T'i+rn BFNEGfl , 1 r - Jt lubbd-LI ,VZ T ', ■■■>.■ J. Or just drag it here! User Guide - Page 21 ...

Switch on the power. The connection and the Ribbon Cable from the Main Drive Motor MOT1 are good. L3, indicates that the Main PWB sensed that the carriage did not return home after power up or after the copy cycle. E7 14 IMAGE PROCESSING PROBLEM The Main PWB sensed a communication problem between the CPU and the image processing (ASIC) chip.

Refer to open the front cover. 3. When I opened the machine to remove the paper jam, there was unfused printed toner on about 2/3 of the page. info WorkCentre XD SERIES REFERENCE SYMBOLOGY Notes, adjustments, and parts lists support the checklists and the RAP information. Thank you for your help.

If the connections are good replace the Lens/CCD Module PL 3.2. I did the on off try and that did not worK. My printer works fine now after reseting the H code. The Auto exposure LED comes on and goes off.

What does dirty look like? Enter diagnostic code 5-2. Thanks so much!! Observe all ESD November 1998 procedures to avoid component damage.

Check the connector PJ CN1 24 on the Main PWB and the ribbon cable going to the CCD PWB for an open or intermittent condition. http://devstude.net/xerox-workcentre/xerox-workcentre-5632-error.php Y N The Ventilation Fan Motor MOT3 is running. Connect the meter to, PJ CN125-2 and GND. When I trunoff the printer and turn it back on the error light goes off and Question about WorkCentre XD155DF Laser Printer 1 Answer Xerox WorkCentre XD155DF front panel error code

The E7-[14] Status Code still exists. Connect the meter on the machine side P/J6 between pins 1 and 2 (refer to Flag 3). If problem still exists, replace the Power Supply PWB PS1.PL 7.1. http://devstude.net/xerox-workcentre/xerox-workcentre-pro-420-j7-error.php Y N Replace the Fuser Assembly, PL 6.1 .

Reconnect all cables and assembly all covers.6. If the wires are good, replace the Registration Roll Solenoid SOL3. Remove that screws and the fuser is free and should slide out.

The drum cartridge indicator on the front of life.

Turn on machine and check again for Fault Code7. Goto A1/A2 Status Code RAP. Procedure Switch on the power. Browse Categories Answer Questions Xerox WorkCentre XD120f Copier Xerox Printer and Copier Printers & Copiers All Unanswered Join Sign In Ask a Question × HomeForumPrinters & CopiersXeroxXerox WorkCentre XD120f CopierL6 Share

Install more RAM in the printer setup dialog. Press the Clear button, press the Exposure Mode button, press the Clear button, andpress the Exposure Mode button.a. Status Code Indicators 11/98 J1 Status Code RAP (With SDF) www.prlhfflbpy.info workCentre xd series TC.kFRC^FTRnC.F PL* 2 F -. Get More Info Anyhow, try to reconnect all connectors on Main PWB.Switch off the Main Power Switch.