Home > Xerox Workcentre > Xerox Workcentre Xd100 L6 Error Code

Xerox Workcentre Xd100 L6 Error Code

It spins to create the scanned image. The E7-[03] Status Code still exists. The L6 error code is: The Main PWB sensed a Polygon motor lock signal error that is related to the mirror motor within the laser. NOTE: If the customer complains that the toner cartridge reached its end of life too soon, then instruct the customer that making copies with the document cover open or making copies useful reference

E7 12 SHADING CORRECTION PROBLEM The Main PWB sensed that the white value obtained when the calibration strip was scanned was incorrect. E7 04 CCD WHITE LEVEL PROBLEM The Main PWB sensed that a problem exists with either the CCD drive circuit or the Exposure Lamp. Y N Replace the Main PWB, PL 7.1 . by unknown on Aug 24, 2011 at 6:31pm Add comment Please sign in to comment 0 My printer has an error code E7 and sub code 15.

If the connections and wires are good replace the Laser Module, PL 3.3. Reflector Clean using Lens and Mirror Cleaner on a lint-free cloth. Heat Roll Lubricate the gear with 8R983 Fuser Lube.

The Motor and drive components are good. Customer's service of equipment, or modules, components, or parts of such equipment may void any otherwise applicable Xerox war- ranties. in xerox 3100mfp Xerox Phaser 3100MFP/S Laser... 2 Answers What's a 016-799 error code mean? If the wires are good, replace the Drum Cartridge Reset Switch, PL 5.1 .

If problem appears again 1st run diagnostic, 2nd reconnect the connectors, 3rd clean the laser unit. Hip Hip Hooray! - jaltizer WORKED LIKE A CHARM ... Press Start. XEROS envoie un technicien pour changer, mais je peux le faire moi-même.

prfM3opy. Clean (with Film Remover only) or replace as required. Machine is very noise. Problem with the laser mirror that spins inside the laser unit.

Switch on the power. If the connections are good replace the Lens/CCD Module (PL 3.2). NOTE: Ensure that the shipping screw was removed at install. NOTE: Ensure that the shipping screw was removed at install.

I do this when servicing/ checking the fuser unit. http://devstude.net/xerox-workcentre/xerox-workcentre-7132-error-code-010-333.php There is approximately 1.2 VDC present. Switch on the power. These symbols are included as an aid to understanding the repre- sentations used in the Circuit Diagrams (CDs).

The Paper Jam lamp comes on and goes off. The voltage decreases to approxi Request unsuccessful. Check the The wires for an open circuit. http://devstude.net/xerox-workcentre/xerox-workcentre-xd100-error-j1.php I replied that I would appreciate more definitive instructions on how to get into the machine - and received nothing in reply. :-( I would have answered by directing me to

Manually rotate the scan shaft to position the carriage in the home position. r. Go to Flag 1 and check the wires for an intermittent condition.

by unknown on Dec 19, 2009 at 6:55am Add comment Please sign in to comment 0 Try the drum reset procedure:Drum Count Reset:(24-7) Enter diagnostics, select '24', 'Print', followed by '7','Print',

Check the following for wear or damage, PL 3.1 : Scan Drive Gear/Pulley Scan Drive Belt Scan cables The components are good. There is 1.2 VDC present while an H3 status code is displayed. Connect the meter on the machine side P/J6 between pins 1 and 2 (refer to Flag 3). by Jetfan65 on Aug 25, 2011 at 1:52pm Add comment Please sign in to comment 0 Exposure problem (the machine didn't see the lamplight).Exposure lamp out.Make sure the exposure reference strip

The laser most likely needs to be replaced Click on the link below to view the Xerox XD100 support page: http://www.support.xerox.com/go/SOHO.asp?KBID=rpss&prodID=XD100&Xlang=en_US&Xcntry=USA&Xtype=support&prodName=WorkCentre Posted on Oct 13, 2010 Helpful 1 Not Helpful Comment Go to Flag 1 and check the Thermistor circuit for a short circuit to ground. by Scytex on Feb 15, 2011 at 2:12pm Add comment Please sign in to comment 0 ok i have a tuffy H4 however I can not get into serivce to reset Get More Info by Scytex on Aug 10, 2008 at 3:11pm Add comment Please sign in to comment 0 Does anyone know how to reset this code There was a power outtage in the

Xerox does not warrant or represent that such documentation is complete, nor does Xerox represent or warrant that it will notify or provide to such Customer any future changes to this If the wires are good, replace the Registration Roll Solenoid SOL3. Section 1 - SERVICE CALL PROCEDURES This section contains the following: Initial Actions/System Checks System Checkout Final Action Initial Actions/System Checks This identifies how to collect the data necessary to decide Clean the follow- ing parts when the total copy count reaches 120,000.

Y N Replace the Main PWB, PL 7.1 . It is a motor inside the laser that has 8 mirrors on it. Switch off the power. There is +5 VDC measured from PJ CN103-3 to GND Y N There is +5 VDC measured from PJ CN103-4 to GND.