Home > Xerox Workcentre > Xerox Workcentre Xd100 Error J1

Xerox Workcentre Xd100 Error J1

If the wires are good replace the Thermistor RT1 , PL 6.1 . Clean the exterior of the machine and provide copy samples of the customers originals. Procedure Switch off the power. Press the C button. useful reference

Switch on the power. TCJhEH ■COPFOl trteurr «iFv 11 SfcE_ -"Ho i-N1 1 l i-i'l : □a In II TOMBR ■LVtfTl&DaE 00 00 ©

Customer's service of equipment, or modules, components, or parts of such equipment may void any otherwise applicable Xerox war- ranties. Y N Go to Flag 1 and check for an open circuit. Press the Start button.

This still works! With Tag Change ®This symbol indicates that the area to which the triangle points has been modified by the tag number in the circle. Reconnect P/J6. Go to Flag 1 .

ity RAPs. GotoU2-[01]/U2-[04] Status Code RAP. Exit Drive Belt, PL9.3 3. The E7-[12] Status Code still exists.

Open then close the Fuser Gate to actuate and deactuate the Fuser Jam Sensor Q3 while observing the Paper Jam lamp. Press the Start button twice. If the connections are good replace the Lens/CCD Module (PL 3.2). Figure 1 Main PWB (With SDF) WorkCentre XD SERIES 11/98 www.prrnUopy.info Status Code Indicators E7-[15] Status Code RAP (With SDF) H2/H3 Status Code RAP (Without SDF) H2, indicates that the Main

If problem still exists, go to Flag 1 and check for a short circuit. Search Fixya Press enter to search. Maybe just need to have the cartridge shook, replaced or it could lastly need ... If the wires are good, replace the Toner Motor MOT4, PL 2.1.

Buy the Full Version You're Reading a Free Preview Pages 134 to 159 are not shown in this preview. http://devstude.net/xerox-workcentre/xerox-workcentre-pro-420-j7-error.php The H4 problem was cleared in one try. Set the meter to measure. If the problem still exists, replace the Power Supply PWB PS1, PL 7.1.

Table 3 Description Procedure Mirror Base Rail Apply a thin film of 70P95 Turbine Oil to the upper surface of the rail. Procedure Switch off the power. Respond to this 0 You have a problem with your fuser. this page You will need to order in a new one or have your existing cartridge refilled.

DOCUMENT JAM SENSED = Signal Name 2. (L) = Logic State when the signal is available in its named state. Procedure Enter diagnostic code 10. If OK, replace the Main PWB,PL7.1.

I didn't realize that after installing the new gear, I had displaced the fuser bulb...

The Toner Cartridge lamp comes on and goes off. Government Printing Office, Washington, D.C., 20402 Prepared by: Xerox Corporation Multinational Customer and Service Education 780 Salt Road Webster, New York 14580 © 1998 by Xerox Corporation. Press the Start button. If the lights do not go out, then repeat step 3 until they do.

Thanks by Anonymous on Dec 5, 2007 at 2:07am Add comment Please sign in to comment 0 Our machine conked out and my husband and I were all set to price Clean (with Film Remover only) or replace as required. If the wires are good, replace the SDF Feed Solenoid SOL1 , PL 9.2. Get More Info The laser warning symbol is repeated in specific service procedures where laser light exposure is possible.

Y N Run several copies to ensure the problem does not reoccur. Question about Xerox Printers & Copiers 1 Answer Keeps showing J1 error, toner light is flashing ...J1 error, toner light is flashing We just installed a new toner cartridge so I info Introduction Other Information Reference Symbology Reference Symbols The reference symbols (icons) used in this documentation denote supportive data which can be found in other sections of this documentation. Switch on the power.

Switch off the power. by copydoc on Sep 25, 2007 at 1:08pm Add comment Please sign in to comment 0 That was it!