Home > Xerox Workcentre > Xerox Workcentre 385 Engine Error

Xerox Workcentre 385 Engine Error

Replacement 1 . WorkCentre 385 12/98 www.printoopy.info General Image Quality Errors Error Status Check Status Horizontal band See also "Horizontal Band" Troubleshooting Flow. 1. LSU (REP 4.14). Question about Phaser 7750DN Laser Printer 1 Answer Xerox phaser 7750gx ...Code 80 Hiya, Can you be more specific regarding the Engine Logic Board Failure as in is it timing, rom/ram, useful reference

WorkCentre 385 12/98 www.pr4ntcsjpy.info REP 4.12 Rear Cover REP 4.13 Top Cover Removal 1. The close proximity of cables to moving parts makes proper routing a must. Charge roller's contaminated. 3. WorkCentre 385 12/98 www.pr4ntcapy.info REP 4.16 Transfer Roller REP 4.17 SMPS/Engine Controller PBA ^ 4.

Then replace the Laser Printer Cartridge, then the LSU Unit (REP 4.14). End WorkCentre 385 12/98 www.printsapy.info Dark Image Background Replace the ELA Unit-PTL (PL 3.1), then the Joint PBA (REP 4.20), then -► Engine PBA (REP 4.1 7), then the Main PBA Exploded View Illustrations An item that is called out on an illustration has a corresponding listing within this section.

LIU PBA (REP 4.18). WorkCentre 385 12/98 www.praitS3py.info No Power (No LCD Display and LED off) Fuser Error Measure the resistance of the Fuser Halogen Lamp at SMPS CN-1 & CN-2 with covers open. Remove three screws. Plug the cable into the connector on the back of the printer.

Replacement 1 . Remove the following: a. Reinstall the components in the reverse order. Stains in paper path. 3.

Reinstall the components in the reverse order. Clean LSU window. 2. Just carefully unstick it from the print head Mar 27, 2009 | Xerox WorkCentre C2424DN All-In-One Laser... 1 Answer L6 error keeps popping up That is a laser error. Side Covers (REP 4.15). 2.

Xerox Phaser 8860MFP... Load the recording paper in the paper feeder. Remove one screw, then remove the exit-lower assembly. Reinstall the components in the reverse order.

Joint PBA 3. see here Press the tab on the under side of the Cradle and firmly slide the Cradle towards the front of the machine to remove. 3. b. Always inspect for pinched, out-of-place, or frayed wiring.

Check transfer roller left and right spring. Loading...Oops :Please try again. Clean the contacts. http://devstude.net/xerox-workcentre/xerox-workcentre-pro-420-j7-error.php Remove the following: a.

Then, remove the Sensor bracket pinch spring, and pinch roller. Removal 1. WorkCentre 385 12/98 www.praitc5opy.info General Error Repair Procedures General Troubleshooting Reference Check for Paper Feed blockage.

Door Open or No Toner 1 .

If there is no cartridge installed, or no paper, the display shows "DOOR OPEN or NO TONER!!!" or [NO PAPER]. 1 . Replacement 1 . b. Wait until components cool before you begin work.

Replacement 4. Scan image OK? 1 . Re-insert the film into the front area. Get More Info Main PBA Connect Cables Connect Cables Possible Cause: 1.

Tell us some more! PDF Manual Guide_EN.pdf. It is recommended that the parallel cable supports IEEE- 1284 bi-directional communications. Main PBA (REP 4.19).

Disconnect the ground wire and connector. Xerox WorkCentre...