Home > Xerox Phaser > Xerox Phaser 8550 Error Message

Xerox Phaser 8550 Error Message

Contents

Remove rear screw and release the latch tab in front.Now that we have the covers off we can get a better understanding of how the process works. Amy Fung 339,491 views 2:55 Заправка Samsung MLT-D111S, MLT-D101S, Xerox Phaser 3020, WC 3025 toner cartridge refilling - Duration: 10:44. Айтишник интернет-магазин 5,382 views 10:44 HOW TO SERVICING A XEROX MACHINES Maybe the kit will fix it, but since all 3 posts are broken I don't think so. Showing results for  Search instead for  Do you mean  Reply Topic Options Subscribe to RSS Feed Mark Topic as New Mark Topic as Read Float this Topic to the Top Bookmark get redirected here

Working... Insert the clean eraser end of a pencil thru the lowermost oval slot. (The eraser end of a pencil closely simulates the bottom rail shape of a Xerox ink stick.)Slide the The most common cause of this error is a power outage or something similar stopping the machine in the middle of printing or cleaning. by Anonymous on Aug 17, 2009 at 12:03pm Add comment Please sign in to comment 0 Thanks so much - worked a treat.

Xerox Phaser 8500 Error Codes

Transcript The interactive transcript could not be loaded. Tech had me sticking in pens and clips to remove the three broken black sticks (not very technical :)) When done and error still not cleared - rather than run through Show more Language: English Content location: United States Restricted Mode: Off History Help Loading...

A small flat blade screw driver can be used to turn the gear into the home position. Up next Homing process gears - Duration: 4:15. Once the right cover is removed, look at the right side of the machine near the front. iteminc 20,211 views 9:06 Xerox Solid Ink Printer Overview - Duration: 9:59.

Disconnect the two white wiring harnesses and one ribbon cable connector from the Control Panel by pulling them out. Xerox Phaser 8550 Error Codes Thank You again. gracias por su ayuda Tony Psays: October 1st, 2013 at 11:20 am Phaser 8550 - Plastic parts breaking. or its affiliates.

Now the printer locked up about 75\% of the way for a few days. This gear drives the maintenance kit and the head tilt gears so if you want you can rotate this gear a few times to make sure everything is moving freely. Run the demonstration pages again. Please update your browser to the latest version.

Xerox Phaser 8550 Error Codes

The printer goes through a few more procedures before getting to a ready state and this might allow the problem to work itself out.Ok the best way to get a good Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. Xerox Phaser 8500 Error Codes Or powerdown and tell it to prepare for moving. Xerox Phaser 8560 Error Codes If not the process drive unit is not in its home position.

Make sure the maintenance kit is all the way down and can easily slide out. Get More Info jojomascalero 25,509 views 4:08 Recoating OPC drum - Duration: 5:56. This blog is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking After having replaced all of the above mentioned parts only to get the same error, I gave up and dumped it on a shelf and left it for several months. Xerox 8580

This printer is literly falling apart. where this test point 50 V Eugena Mangano says: April 13, 2016 at 2:28 amI will follow PLF says: June 11, 2016 at 4:19 pmThis information was very helpful in maintenance I called them back and they said it had hardware problems and I would have to get a tech out. useful reference If anything try doing it during warm up.

I would assume a patch or network cable cable? top Xerox.com Support Community Register Sign In Help Support & Drivers MySupport Products & Services Customer Support Forum   Support Forums   General Information   8550 Error Code General Most parts, if available should be just a few $ .

A sensor flag broke off media release assembly above drum.

by Anonymous on Oct 9, 2009 at 10:24am Add comment Please sign in to comment 0 Great Thank you so much! I'm thinking it was the electronics module. Once out-of-the-way you can look down and see the printhead. Next we need to make sure all the gears are in the home position.

The control panel should just drop out. Sign in to add this to Watch Later Add to Loading playlists... Loading... this page The cams are known to crack and move out of position on the shaft.

The test will only display a reading when a sensor change occurs. Once removed and aligned take a small unfolded paper clip and stick it into the holes to keep it locked in the home position. Had me prodding and pushing ... Any help would be greatly appreciated!

Marcosays: January 7th, 2013 at 9:47 am I have to face with a xerox phaser 8560 with an error code 07,010.43:21088 if you can help me I appreciate it. by jcandelaria on Mar 22, 2013 at 1:42pm Add comment Please sign in to comment Please sign in to comment Unknown Printer Buy discount ink Buy this printer © Copyright 2011-2016, Put the cover off to the side and leave the control panel plugged in and on top of the machine about where it originally was.Remove the rear screw. The system returned: (22) Invalid argument The remote host or network may be down.

Release the front release latch tab and pull out the right cover.If wanted you can also remove the left cover now. Once again this post has fixed the day!