Has to do with the black ink stix and loader. Visually check these for cracks or being broken. How to fix ? Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... get redirected here
iteminc 6,977 views 4:15 Pitva: vosková tiskárna Xerox Phaser - Duration: 9:48. If both parts look ok, then a tech may just need to come out and rehome the printer for you. Viridel648 25,133 views 9:41 Don't buy Xerox Phaser Printers - Duration: 2:57. Put the cover off to the side and leave the control panel plugged in and on top of the machine about where it originally was.Remove the rear screw.
Gently shake the gear pack. If not the process drive unit is not in its home position. Sign in to add this video to a playlist.
Loading... Insert the coin under the left corner of the Control Panel cover, and then turn the coin upward until the Control Panel cover is released from the left side cover assembly. Natahasays: April 16th, 2013 at 10:07 am
Turn the printer on and watch it warm up. On the left you should see a big black plastic piece that blocks your view of the front of the printer. Xerox 8550 Service Manual Error codes starting with:09,035 09,000 09,008 09,01809,036 09,005 09.015 09,02509,037 09,006 09,016 09,02609,038 09,007 09,017 09,027The Ink loader current part numbers are:8400 - 200-4698-808500 or 8550 - 133K277118560 - 133K27771http://www.iteminc.com to So with the maintenance kit removed pull up on the pivot plate and with a flashlight check the back of the cams for cracks.
This can cause all sorts of problems including the 07,010.43 error. Get More Info Also add two short screws where plastic location projections were. There is very little space to remove objects from this area, so I recommend anyone else who experiences this to be patient and take your time removing any obstacles to avoid Make sure everything is back the way it should like the maintenance kit installed, the front and exit cover closed, and the control panel is sitting on top of the machine.
Use a small coin to release the Control Panel cover from the top of the printer by following the steps below: Insert the coin under the right corner of the Control Cleaning the printhead on the Phaser 7800> Phaser 8500/8550/8560 07,010.43 error code August 8th, 2012 at 1:31 pm This error pops up when the printhead in your printer cannot move back Now the printer locked up about 75\% of the way for a few days. useful reference Rogerio Passy 633 views 2:57 85 videos Play all US TOP 40 SONGS THIS WEEK NOVEMBER - NEW MUSIC 2016SanPauloTORINO Another Inconvenient Day with Solid Ink - Duration: 5:16.
Turn the Control Panel over and place it on top of the printer. Sign in Transcript Statistics 43,103 views 26 Like this video? Sign Up Login Add Question stingray asked Dec 14, 2006 at 4:30am 0 Unknown Printer Phaser 8550 error code 09,038.46 Hello!I´m dealing with a printer that reports 09,038.46 immediately after power
The white gear on bottoms home position is at 6:00 o'clock and the black one on top is around 11:00 o'clock. Up next Xerox Colorqube 8570 & 8580 Remanufactured Ink Blocks - Duration: 9:41. The process drive unit drives the transfix, printhead tilt, and the maintenance kit. Once the right cover is removed, look at the right side of the machine near the front.
This gear pack is screwed into the frame via some plastic mounts. Turning on the printer and as XEROX appears on the screen, press and hold the Back and Help button until Beginning Service Mode Initialization appears.b. LJBvideos 31,605 views 5:16 Xerox Phaser 8400 8500 8550 8560 Error Codes 09,0xx ink loader replacement - Duration: 4:19. this page Xerox® and Xerox and Design® are trademarks of Xerox Corporation in the United States and/or other countries.
Best to move clockwise. iteminc 29,601 views 2:26 Xerox Phaser 7700 / 7750 /7760 Imaging Unit OPC Drum Tambor V2 - Duration: 8:01. The problem is that error code is not described in service manual, so I don´t know where to start. Rating is available when the video has been rented.
I am wondering if any one has any idea what that is and how to fix.Thank u!E by unknown on Aug 17, 2012 at 7:24am Add comment Please sign in to Caution the ink loader has cables running along the bottom of it but you should be able to move it back slightly and sit it on the rear of the machine. Install all screws before fully tightening them. This is the pivot plate and it pushes the maintenance kit to the drum to oil it.
by Anonymous on Aug 27, 2009 at 1:51am Add comment Please sign in to comment 0 Thank you!!!!!!!!!!! LifesaverRegardsDavid by scrimcity on Oct 15, 2009 at 8:44am Add comment Please sign in to comment 0 Thank you printerfixer so much!I have a Phaser 8560, but it works.