Home > Xerox Phaser > Xerox Phaser 7700 Error 54 Fan Failure

Xerox Phaser 7700 Error 54 Fan Failure

Contents

iteminc 37,592 views 2:14 steve jobs on why xerox failed - Duration: 2:55. Did the test pass? Cycle power to the printer to clear the error.2. Need Part? get redirected here

Click Order Fuser click hereHave Questions? Ensure the Process Drive is correctly aligned and homed. Uploaded on Dec 29, 2009http://www.iteminconline.com1-800-367-4836If you have a Xerox Phaser 7750 with error code 48 or a 7760 with error codes 010-391, 010-392, or 010-398, this video will show you how Xerox Phaser Printers &...

Xerox Workcentre 7335 Error Code List

Click engine control board click here Have Questions? Did the error clear ? we have lots of works to do, and urgently our printer's problem must be solved.

You have to remove the back, right side and top cover to access that fan.It is near the back just behind the fuser module. If yes Replace the Tray 1/MPT assembly. It has been my experience that 90% of the time the scanner motor (polygon motor) has gone bad. Xerox 6700 Engine Sensor Failure Loading...

Ensure the Process Drive is correctly aligned and homed. Xerox Phaser 6700 Error Codes Head Maintenance Clutch. No charges, completely free! Need Part?

Click electronic module click hereHave Questions? Inspect the accumulator belt home sensor; clean if necessary.7. Need Part? Sign in to make your opinion count.

Xerox Phaser 6700 Error Codes

Sign in to make your opinion count. They are not that expensive so order both. Xerox Workcentre 7335 Error Code List Enter service diagnostics.3. Xerox Phaser 6700 Service Manual Aim Live Chat Xerox Phaser 8400 Error 37.022.40Error Description: Pressure pump motor disconnect.Possible Solution: Run the Pressure Pump Motor test.

Click Process Drive Assembly Head Maintenance Clutch Have Questions? Get More Info Carefully reinsert the plugs into their joint socket and FIRMLY seat them.4. Does the motor run? Once you remove the fan, there is a label on it, remove the label, There is a rubber plug behind the label, remove the plug and drip some lubricant into the Xerox Phaser 6700 Fault Codes

Then, you have to measure the resistance between the fuser assembly connector P600-4 and P600-6. iteminc 3,535 views 12:27 How to repair Xerox Phaser Blank/Bad Screen Display - Duration: 6:45. Click Process Drive Assembly Head Maintenance ClutchHave Questions? http://devstude.net/xerox-phaser/xerox-phaser-7700-error-30.php Corporal: An expert that has over 10 points.

Follow these steps to check your printer .Verify the Process Drive system is properly homed, if not properly homed remove the process drive motor align it and re-install , and power Error Code 12, 13 ,14 and 15: ATC Sensor Failure Solution: Remove the Rear Cover , and Rear Shield , Measure the voltage at P534-5 on the Engine Control Board. Then, you have to disconnect P400 and P401 which is on the engine control board.

iYogi has no affiliation with any of these third-party companies unless such relationship is expressly specified.Technical support may be provided by the brand owners.

I would recommend replacing the defective fan though. If the problem persists, replace the Engine Control Board (116-1144-00). Showing results for  Search instead for  Do you mean  Reply Topic Options Subscribe to RSS Feed Mark Topic as New Mark Topic as Read Float this Topic to the Top Bookmark NEED PART?

About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! Aim Live Chat Xerox Phaser 6250 Error Code 81 Error Description: Controller to Engine Communications Failure Possible Solution: Cycle power to the printer. We are now happy to extend to you our full-service, efficient, and cost effective electronics restoration. http://devstude.net/xerox-phaser/xerox-phaser-7700-error-13.php If the resistance measure is not between 20k and 100 ohms, you have to replace the fuser assembly.

Open the RH Door and defeat the interlock switch. Re-engage, if necessary. Does the voltage measure between +1 VDC and +3 VDC ?