Click process motor click here transfix cam click here Have Questions? Did the test pass? When this failure occurs, you have to switch off the printer and remove the fuser assembly. If problem reoccurs . http://devstude.net/xerox-phaser/xerox-phaser-7700-error-13.php
CLICK Engine Control Board click here image processor click hereHave Questions? Go here to order this parthttp://www.iteminconline.com/itemdesc...For installation instructions, follow this link: http://www.youtube.com/watch?v=65NT-f...Feel free to give us a call at 1-800-367-4836 if you have any questions or visit us at www.iteminconline.com. Our award winning and low priced Annual Subscription covers the following services: Comprehensive support for fixing Xerox Phaser printers error Codes Diagnostic & repair for your technologies. Check the Purge Pump wiring.
Aim Live Chat Xerox Phaser 7700 Error Code 11 Error Description: LASER UNIT POLYGON MOTOR FAILUREPossible Solution: Remove Rear Cover , Disconnect P400 , on the Engine Control Board.Inspect both connectors Error Code 30: Accumulator Belt home position took too long Solution: Ensure the Accumulator Belt shipping restraints have been removed. If not connect them.Remove and reseat ROS Harness connector J151 to the Laser Unit.If the error persist, replace the following parts. under this sub menu will be 4-5 options of erros to clear, the first one should be for error 30-belt home to long.
Replace the following parts: Process Drive Assembly . If problem persists Test the ink melt heaters.Run the appropriate Ink Melt [1, 2, 3,4] Heater test in diagnostic menu.Replace the Ink Loader. If yes: Replace the Engine Control Board If no: Remove the Rear Cover , the Rear Cover Shield , Measure the voltage at the Print Engine Controller Interface Board P407-4(+) and printerbase.co.uk 10.507 görüntüleme 3:45 Recoating OPC drum - Süre: 5:56.
If the problem persists, replace the Laser Unit ,and , or , the Engine Control Board (116-1144-00). Aim Live Chat Xerox Phaser 7700 Error Code 54 Error Description: FAN FAILUREPossible Solution: Enter Service Diagnostics Mode. , Run the "Fuser Fan" test. Is the voltage between +1 and+3 VDC? Remove any obstructions.4.
According to Computer Shopper Magazine (1999), "One of the best ways to save begins with the acceptance of the idea that most refurbished equipment isn't inferior." Our pre-owned best value hardware Reboot the printer.Did this correct the problem? Start troubleshooting If your printer is networked, it can actually communicate with our support knowledge base directly, and troubleshoot itself. This cleared the error for me.
Does the Fuser Fan operate? You have to reinsert the plugs in their join sockets carefully. Then, you have to measure the resistance between the fuser assembly connector P600-4 and P600-6. Enter service diagnostics.3.
Posting Guidelines Promoting, selling, recruiting, coursework and thesis posting is forbidden.Tek-Tips Posting Policies Jobs Jobs from Indeed What: Where: jobs by Link To This Forum! http://devstude.net/xerox-phaser/xerox-phaser-7700-error-code-13.php Are the cams damaged ? If yes , go to the next step.If no, replace the eeprom board. Need Part?
X All Science and Technology Hardware Issues Drivers Multimedia Software Operating Systems Security Software Networking Security PC Optimizer Internet Browsers Communication Software Publishing Software Productivity Software Graphic Design Software Issues Hardware Bu tercihi aşağıdan değiştirebilirsiniz. Aim Live Chat Xerox Phaser 7750 error codes, xerox troubleshooting, phaser errors, phaser jams, xerox jams, xerox phaser error messages Xerox phaser 7750 Error Code: 80Error Description: Engine Logic Board Failure, useful reference Reinstall the fuser assembly.2.
Does the error persist? Replace the Ink with Xerox Ink. Remove any spilt ink or, any loose ink from the area of the head tilt gear.
Have Questions? If yes , replace the engine control board Need Part? hope this helps. Renew for just $119.99 more detail Buy now You can also go through our resources to find help: Video Tech Talk Why Is My Computer So Slow?
Click Order Fuser click hereHave Questions? by CatherineJ on Sep 10, 2008 at 6:34pm Add comment Please sign in to comment 0 Not sure if it helps but i had to download the Error 30 reset procedure Printer Xerox Phaser 7700 error codes ► February (10) ► January (6) ► 2010 (32) ► December (7) ► November (4) ► October (2) ► September (1) ► August (1) ► this page It is a low cost printer.
Click main motor assembly engine control board Have Questions? Is there a diagnostic mode or reset function? Does the resistance measure between 20K and 100K ohms? Replace the electronics module Need Part?
All rights reserved. Slow PC? 3 Musketeers Will Make Your PC Run Faster This happens all the time – you buy a new ... If no, got to next step . It has more hard disk space.
Carefully reinsert the plugs into their joint socket and FIRMLY seat them. Need Part? Libellés : Xerox phaser No comments: Post a Comment Newer Post Older Post Home Subscribe to: Post Comments (Atom) SSC Service Utility Software to reset Epson printers Canon Inkjet Printheads Error Have Questions?
if a particular error occurs 3 times then it needs to be cleared after the problem is resolved. Check the Purge Pump wiring. Does error recur after the Fuser Assembly has been replaced?Replace the Fuser Assembly. If yes your complete .
Nate Watson 27.919 görüntüleme 3:00 Replacement of Phaser 7760 Presure Film - Süre: 1:27. Aim Live Chat Xerox Phaser 6250 Error Code Instal or Reseat FuserError Description: Install or Reseat FuserPossible Solution: 1 Cycle power to the printer. Automated Remote Diagnostic Tool - PhaserSMART™ Support Options Contact Xerox Support for help with this product. Careers Contact Us About Xerox Investors Privacy Legal Privacy Choices Site Map © 2016 The test point is located on the power control board below the main board RAM DIMMs.
Join Us! *Tek-Tips's functionality depends on members receiving e-mail. Head Maintenance Clutch.