Home > Xerox Phaser > Xerox Phaser 7700 Error 13

Xerox Phaser 7700 Error 13

Is the consensus to replace the print cartridges? Loading... In the picture it is very clear the drums are contaminated, and since they all are, swapping them is not really going to help. - detonation 0 OK, @Printergodless. I scraped off some of that developer with a sheet of paper and in fact managed to get the machine in perfect order with that again. http://devstude.net/xerox-phaser/xerox-phaser-7700-error-30.php

Does the Fuser Fan operate? Xerox® and Xerox and Design® are trademarks of Xerox Corporation in the United States and/or other countries. Seems like if the wiper on that drum were bad, then I'd see red tire tracks ?Any idears ?thanks much, still have 180 of those pages left to print, hopefully soon French Site L'imprimante en question Friends Archaeology news Libellés Brother (7) Brother DCP (6) Brother HL (1) Brother MFC (7) Cano IR (1) Cano S (1) canon (29) Canon BJC (2)

Error Code 12, 13 ,14 and 15: ATC Sensor Failure Solution: Remove the Rear Cover , and Rear Shield , Measure the voltage at P534-5 on the Engine Control Board. Ensure there is noseparation.Carefully reinsert the plugs into their joint socket and FIRMLY seat them.Replace the Laser Unit (RRP 38, on page 7-184).Note Whenever the mounting screws for the Laser Unit And i'm not exactly sure which sensor it may be.Thanks for any help,Nick Respond to this 0 i believe you must go into the tech menu and reset the tech rep Taking them out and rotating the cart doesn't seem to be clearing the toner off.

Sometimes developpers can go bad and that will show up as a light or dark streak in the process (paper travel) direction. iteminc 19,523 views 5:28 Xerox Phaser 8400 8500 8550 8560 Error Codes 09,0xx ink loader replacement - Duration: 4:19. by unknown on Apr 2, 2009 at 7:07pm Add comment Please sign in to comment 0 OK are any of you guys X Xerox techs like me, just wanted to know. Close Yes, keep it Undo Close This video is unavailable.

Once again the machine was getting some what low usage and never been serviced so not typicall to replace all at once but it does happen. by detonation on Oct 26, 2006 at 1:09am Add comment Please sign in to comment 0 Are you using the postcript driver ? Generated Tue, 02 Aug 2016 05:21:52 GMT by s_rh7 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection is this a nvm problem?

by printergodless on Feb 4, 2009 at 9:25am Add comment Please sign in to comment 0 I received a developer, which is essentially a bag of liquid. by unknown on Apr 29, 2008 at 3:43am Add comment Please sign in to comment I have similar problems (again) with a 7700 I recently acquired. Your cache administrator is webmaster. I have a feeling it's one of the sensors in the printer itself and not on the belt but i can't get any part numbers etc for the sensor.

Last night I dreamt of this printer ;-(... I'm not sure I'd just replace the wiping blades. "The printer is complaining that cart #3 needs to replaced soon, but I think that's based on page count, no?"Afaik the PC's by unknown on Apr 1, 2009 at 8:55am Add comment Please sign in to comment 0 FYI renart,The first basic test you should do is to swap print cartridges to see Once you've found the drum that has this problem, replace it, and your problem should be fixed. - detonation 0 Looks like the cleaning blades in the image unit are failing.

So far i've changed the black toner, fuser and transfer roller with no change.Thanks... http://devstude.net/xerox-phaser/xerox-phaser-7700-error-code-13.php The system returned: (22) Invalid argument The remote host or network may be down. Try using the RejiCon Adjustment. Fix your printer !

If the problem persists, replace the Laser Unit ,and , or , the Engine Control Board (116-1144-00). I also have access to the service manuals and bulletins. Replace the Laser Unit , If the problem persists, replace the Engine Control Board (116-1144-00). useful reference If yes: Replace the Engine Control Board If no: Remove the Rear Cover , the Rear Cover Shield , Measure the voltage at the Print Engine Controller Interface Board P407-4(+) and

Instead when I push ok, it just goes back to the previous menu.Any help or suggestions on where to go from here will be appreciated!Thanks! iteminc 42,963 views 4:19 how Laser Technology Process animation - YouTube.WEBM - Duration: 2:56. I then went to the 'clear tech rep faults menu'.

Or is there a sensor?

Swap the Print Cartridges. All rights reserved. But for instance a cloudy sky or a green leave looks like crap. After printing the test pages i realized that the image is heavily messed up.

Error Code 30: Accumulator Belt home position took too long Solution: Ensure the Accumulator Belt shipping restraints have been removed. Sign Up Login Add Question detonation asked Oct 13, 2006 at 1:13am 0 Xerox Phaser 7700 Xerox Phaser 7700 bad quality I thought I posted this already but can't find my I moved the black to the right, and juggled the others around. this page THANK YOU!

Does the voltage measure between +1 VDC and +3 VDC ? Start troubleshooting If your printer is networked, it can actually communicate with our support knowledge base directly, and troubleshoot itself. If the banding frequency is high (.5 mm), replace the Laser Unit by unknown on Nov 2, 2006 at 2:03pm Add comment Please sign in to comment 0 Detonation, When you Sign in to make your opinion count.

now clear the jam and run one sheet. I'll also try to get a good scan of a print up, I'm not sure my dad's scanner is good enough though. Loading... Register now while it's still free!

Now did you setup the tray you are printing from as the same media size and type ? if not then the drums, laser and dev housings are ok. I thought the wiper on the black print cartridge but I switched cartridges with magenta, no difference. First of all, it gave a really uneven print in some of the color, which I eventually pinned down to a bad cartridge (cyan).

If yes: Reinstall Fuser, Remove the Rear Cover, Rear Shield and the Rear Shield Bracket , Measure the resistance between P404A-1. It may also clear up corrupted settings.Good Luck. Shut down machine, let it cool for at least 20 minutes and then take the fuser out. by detonation on Feb 8, 2011 at 11:20pm Add comment Please sign in to comment 0 Thanks for the replies.

Show more Loading... The xerox's do have a troublshooting menu. But like printergodless points out you really do need some technical dexterity and above all the service manual. If your dealing with faded print.

Still a black tire track. Use extreme caution to prevent burns. Close Reply To This Thread Posting in the Tek-Tips forums is a member-only feature. by nivek on Mar 31, 2009 at 2:42pm Add comment Please sign in to comment 0 Hmmm...looks like you guys may have called it.