Home > Xerox Phaser > Xerox Phaser 7700 Color Laser Printer Error Code 13

Xerox Phaser 7700 Color Laser Printer Error Code 13

Ensure the Process Drive is correctly aligned and homed. Follow these steps to check your printer .Verify the Process Drive system is properly homed, if not properly homed remove the process drive motor align it and re-install , and power But for instance a cloudy sky or a green leave looks like crap. Make sure you select the proper media setting otherwise it will affect the print quality. http://devstude.net/xerox-phaser/xerox-phaser-7700-error-code-13.php

I'll try to look more into color calibration though. Click process motor click here transfix cam click here Have Questions? If yes , Replace the Electronics Module. Last night I dreamt of this printer ;-(...

It's pretty labour intensive to get the developer out. Remove the rear cover from the printer.2. From the Sensor Tests run the Fuser Temperature test.4.

Need Part? Reboot is the problem fixed? Hope you have luck finding replacement wipers! - detonation 0 Well someone did post to try and switch the drums around and see if it follows like your yellow looks like started troubleshooting .i started fixing one thing after the other and was getting better and better then one of my problems was with the developers i looked at the ATC values

Check the ATC sensor wiring harnessYellow = P/J129Magenta = P/J 130Cyan = P/J 1312. Please try the request again. I have seen cases where technicians would replace parts to fix a poor transfer issue when all that was needed was to calibrate all the media to get the proper transfer.Poor Is the wiring damaged?Replace the purge pump.

Also you should print the repeating defect page to help pindown the source of the problem. The system returned: (22) Invalid argument The remote host or network may be down. As the developer beads are pretty expensive (especially if more than one color is depleted) I tried to use developer from a defect 7700 which I used as donor machine. Aim Live Chat Xerox Phaser 6300/6350 Error Code 50Error Description: Fuser Fan Failure Possible Solution: Check the Fuser Fan for damage.

If you can find someone who sells just the blades then you can replace them. We are now happy to extend to you our full-service, efficient, and cost effective electronics restoration. If yes , your issue has been resolved.If no , replace your laser unitIf the problem persists, replace the engine control board.Need Part? by Anonymous on Apr 2, 2009 at 8:39am Add comment Please sign in to comment 0 I think you should get a tech in to look your problem or order one

If yes , Replace the Electronics Module. Get More Info Moving them around changed the tone of the backgrounding, but didn't fix the problem.NONE of the drums have been replaced and it has been left standing for a few years. Your cache administrator is webmaster. I cant tell you the amount of calls we get for quality problems due to poorly made third party cartrdiges.

Either way, I think it is toast. Did this clear the error? by subs on Aug 20, 2010 at 5:48pm Add comment Please sign in to comment What happens when you switch the imaging unit of black for another color (for example magenta)? http://devstude.net/xerox-phaser/xerox-phaser-7700-error-13.php Ensure the Process Drive is correctly aligned and homed.

Need Part? If yes , go to step 2Check the Fuser Assembly for fault or damage if yes,Replace the Fuser Assembly,If problem precise Replace the Engine Control Board, .Need Part? by nivek on Mar 31, 2009 at 2:42pm Add comment Please sign in to comment 0 Hmmm...looks like you guys may have called it.

Replace the Ink with Xerox Ink.

If no Replace the engine control board.Need Part? Shut down machine, let it cool for at least 20 minutes and then take the fuser out. Your cache administrator is webmaster. Aim Live Chat Xerox Phaser 7700 Error Code 11 Error Description: LASER UNIT POLYGON MOTOR FAILUREPossible Solution: Remove Rear Cover , Disconnect P400 , on the Engine Control Board.Inspect both connectors

This is a high volume printer so most people go through these at least once or twice a year and the blades dont fail within that time so given the cost Error Code 54: Fan failure Solution: Enter Service Diagnostics Mode. by unknown on Apr 2, 2009 at 7:07pm Add comment Please sign in to comment 0 OK are any of you guys X Xerox techs like me, just wanted to know. this page by Stephen on Oct 18, 2006 at 5:01pm Add comment Please sign in to comment 0 Print quality tips, First get the best paper quality, it really matters.

If yes , Replace the ATC Sensor and/or wiring harness.Note: ( the atc sensor and wire harness is part of the developer housing assembly.) 1. Are the cams damaged ? Have a look at the toner waste path, from the PC gate to the toner waste cartridge (make sure it's not full) and also the auger motor, if this fails it Click electronic module click hereHave Questions?