The GPU just needs to be reflowed using the profile available on here, but you need to leave the griddle on for 30 minutes after the repair. And this was with the soldering iron set to 430 degrees Celsius. Ive done the Xclamp method and it is still broken. Xbox 360s are cheap though and if you do decide to reflow you could probably try it for awhile if you got the cash to pick up another phat 360 to http://devstude.net/xbox-360/xbox-360-error-73-solution.php
Now, I just keep getting constant errors every time I try to read from the damn NAND, but never at the same place and never the same errors, either. The most time that I've played on this console is like 3 straight hours of gameplay. Ececpt they had nothing to do with any chip. This particular Xbox 360 suffered from the E74 error with secondary code 1022, which meant that the HANA scaler chip had a problem.
Get the answer beanoslim 13 January 2011 19:42:00 I did the towel trick once and its worked ever since, months and months ago. tomi_the_great on 2010-08-15 16:04:42 : reflow for 5-10 minutes with fan turned off works for me. Should I offer to apply the 12V fan mod on those broken Xbox 360s? after 5 minutes i turn off the sexbox and turnit on again and the 2rrod shown.
Sign in Transcript Statistics 60,859 views 152 Like this video? Loading... That "aud_clamp" mod is recommended for any systems with HDMI ports but on Zephyr it's meant to alleviate the excessive problem with E79. P0102 You need to let the flux go in between the die and the motherboard, as that's where the solder is.
TmEE, did you perform the JTAG exploit? On one of the on/off fits this Xbox 360 now pulls off, the 4 lights on the Ring of Light were red and none were flashing. Please allow up to 5 seconds… DDoS protection by CloudFlare Ray ID: 2fc038bce68016be Log in or Sign up Search Search titles only Posted by Member: Separate names with a comma. E06: GPU over heating -ensure your x-clamps are installed properly.
Connect with top rated Experts 19 Experts available now in Live! Xbox 360 Error Codes There are two theories to fixing this one deals with the "X" clamps that hold down the chips. Also, at one point, all those lights were ORANGE. After heating is done the GPU will have descended 0.1mm and all joints are connected and will be slightly fatter too thus possibly being stronger...
I will have to restart the XBOX 360. Needless to say, I wasn't very pleased. Rrod 0102 GPU has a sensor of its own inside it aswell as CPU, XSB has a heat sensor too IIRC... 0102 Phone Number This Falcon 360 has the dual heatsink on the GPU, which works a lot better than the stupid single heatsink used on Xenon and Zephyr Xbox 360s.
slingblade1170, Jan 28, 2014 Top #10 (You must log in or sign up to reply here.) Show Ignored Content Share This Page Tweet Log in with Facebook Your name or email my review here With that, there's a risk that other solder joints will crack. E07: RAM over heating E08: Unconfirmed: General I/O Malfunction, could be caused by an error with any of the I/O devies such as A/V port, USB, Hard drive, DVD drive, etc. and therefore, like most steel, will lose its retention strength... (basically as time goes by... 0102 Country Code
The detailed description is: Mfgbootlauncher Unable to parse the host response (factory command) Mfgbootlauncher problem with Base64 encoding Christmas lights? after 5 minutes i turn off the sexbox and turnit on again and the 2rrod shown. For sure one of the balls didn't attach properly! click site Was about to replace GPU when decided to do further testing.
i play GTA4. and its ridiculous how fast burning/reading happens on X360 itself, just in matter of seconds :O Ace08-14-2010, 03:59 PMTell me about it. Pressure on ram chips still yielded 0102.
I have yet to stress test that system, but I will get to it later. Posted: Thu Apr 19, 2012 4:26 pm M4C 1K Rainmaker Status: Offline Joined: Mar 20, 20115 Year Member Posts: 3,915 Reputation Power: 191 Already a sticky for this 0useful0not useful #3. I don't know if the mode of my LPT port has anything to do with it(it's set to SPP mode). My PC is really on the edge, if I do something while dump happens I'm going to get errors.
Rating is available when the video has been rented. No need to worry about that. Its extra insurance.. http://devstude.net/xbox-360/xbox-open-tray-error-solution.php The same thing happens with the Xbox 360's GPU: the solder joints are too weak, they heat up, and break.
E34: Error is completely unknown E35: over heating GPU possibly due to lack of thermal compound. EDIT: Oh God, someone help me! DO NOT attempt either of these if your console is still under warranty. This might also be caused by a bad SATA cable.
Apply flux until it overflows to the other side of the GPU die. Had a reballed GPU Xenon come back to me. But since you already have it working, you might want to move one of the JTAG patch wires from the ARGON bus (ARGON = RF board) and connect to "AUD CLAMP". It's supposed to finish in about half an hour, but whenever I do an NAND dump, it takes 4 hours per dump.
Ace08-12-2010, 03:58 PMRight now, I'm just reading the NAND, but when it comes time to write to the NAND, I'm going to remove resistor R6T3, the one that allows eFuses to Also this can be caused by a problem with the fans that make them draw too much power, it can also be caused if you have unnecessary accessories attached to the Reflowing will cause the RROD to come back sooner or later anyway. I don't know how long it is, but it still took a few hours to dump the NAND.
Sounds Good? So I left the XBOX 360 turned on for 40 minutes and then restarted the XBOX 360 then it worked. E68: Hard Drive Error - Hard drive not DMA configured: It could be a problem with the Hard Drive itself or a problem with the internal connection to the hard drive, RRoD solutions!
JYP666 on 2013-04-01 16:28:11 : 0102 on a Xenon board. This is what happened during my last dump in the NANDPro debug log(NANDPro is used by iHc Xbox 360; it's just a simple all-in-1 tool for game mods and for the for dumps I used a 4 meter heavily shielded LPT cable and I did not have more than 2 ground wires in use, neither connected to exterior. Ask!
goodolick on 2011-07-30 18:01:34 : Can confirm sometimes CPU. OK, if you took the time to visual, you should be able to figure out that pulling DOWN on each corner on the X while pushing UP in the middle of Microsoft covers this error under their 3-year warranty, this is availble to anyone who hasn't modified their console. Many people experience problems with the CPU AFTER the X-clamp fix... (see bottom of post for x-clamp replacement recommendations) Soo, the X-clamp, This is where are problems begin...