Home > Socket Error > Wsa Socket Error 10004

Wsa Socket Error 10004

Contents

How would you know what went wrong? WinSock description: The 'address' it refers to is the remote socket name (protocol, port and address). An existing connection was forcibly closed by the remote host. WSAEFAULT 10014 Bad address. http://devstude.net/socket-error/wsacancelblockingcall-wsaeintr-error-number-10004.php

WinSock only allows a single blocking operation to be outstanding per task (or thread), and if you make any other function call (whether or not it references that or any other Under MS-DOS versions 3.0 and later, EACCES may also indicate a locking or sharing violation. This is one of the most frequent errors and one of the best to encounter, since it's one of the least ambiguous. ChoAnderson Administrator A.2 Windows Sockets error code extensions described Here are WSAGetLastError () function returns a list of possible error codes in alphabetical order , and gives a brief description of

Socket Error 10054

The file's permission setting does not allow the specified access. This error is returned from operations on nonblocking sockets that cannot be completed immediately, for example recv when no data is queued to be read from the socket. In addition, one or more operations are in progress , if the connection due to "keep-alive" activity detecting a failure while the interrupt , can also cause this error. Format error: Name server was unable to interpret the query.

  • For information on how to handle error codes when porting socket applications to Winsock, see Error Codes - errno, h_errno and WSAGetLastError.
  • This is a common problem.
  • The server application might need to call htons() to translate the port to network byte order in the sockaddr structure.
  • User suggestions: see WSAECONNABORTED for details.
  • Microsoft C description: Permission denied.
  • An operation was attempted on something that is not a socket.

WinSock description: Almost same as Berkeley. An application used a Windows Sockets function which directly maps to a Windows function. This normally results if the peer application on the remote host is suddenly stopped, the host is rebooted, the host or remote network interface is disabled, or the remote host uses Wsagetlasterror 0 TCP/IP scenario: A connection will timeout if the local system doesn't receive an (ACK)nowledgement for data sent.

In this case, it might be possible to check the count of TCP RST packets received, or ICMP Port Unreachable packets. Note that this error is returned by the operating system, so the error number may change in future releases of Windows. User suggestions: Check the obvious first: check that the destination address is a valid IP address. You cannot use more than one WinSock implementation simultaneously.

The Full Code #include #include #pragma comment(lib,"ws2_32.lib") int main() { WSADATA WsaDat; int nResult=WSAStartup(MAKEWORD(2,2),&WsaDat); if(nResult!=0) { std::cout<<"WSA Initialization failed: "<

Socket Error Codes Linux

A service provider returned a bogus procedure table to Ws2_32.dll. WSAENOPROTOOPT (10042) Bad protocol option. Socket Error 10054 The requested service provider could not be loaded or initialized. Socket Error 10053 Binary Countdown Length Proof of the undecidability of the Halting Problem How to deal with a coworker that writes software to give him job security instead of solving problems?

Note that this error is returned by the operating system, so the error number may change in future releases of Windows. More about the author Do a traceroute to try to determine where the failure occurs along the route between your host and the destination host. The ICMP message means that a router can't forward the IP datagram, possibly because it didn't get a response to the ARP request (which might mean the destination host is down). Check that your network system (WinSock implementation) has a utility that shows network statistics. Socket Error 10054 Connection Reset By Peer

Can indicate a service provider implementation error. Which is the error we intended to get, with our little test. However, they don't need to set the WinSock error value, because there's only one reason for their failure: the input parameter was invalid. check my blog WinSock description: No error.

An established connection was aborted by the software in your host machine, possibly due to a data transmission timeout or protocol error. Socket Error 10061 Connection Refused How would a society develop that has no sense of value or ownership? WinSock description: No equivalent.

Berkeley description: An operation that takes a long time to complete (such as a connect()) was attempted on a non-blocking socket. (see ioctl()).

WSAEISCONN (10056) Socket is already connected. After filling out our SOCKADDR_IN struct (refer to tutorial 2) we bind the socket, remember? This is usually caused by one or more of the function pointers being NULL. Winsock Error 10061 WSAHOST_NOT_FOUND 11001 Host not found.

WSA_E_NO_MORE 10110 No more results. Prerequisites Project type: Console Include files: winsock2.h Library files: ws2_32.lib Error Handling You would remember in our previous tutorials that first we must initialize Winsock. I will sometimes get the error 10004 -> http://support.ipswitch.com/kb/WSK-19980714-EM08.htm Caused because i'm ending the program on a blocking call Do you think it is fine to just detect if this certain news This message has a slightly different meaning from WSAEAFNOSUPPORT.

WSA_NOT_ENOUGH_MEMORY 8 Insufficient memory available. WSAEPFNOSUPPORT 10046 Protocol family not supported. SO_DEBUG, SO_DONTROUTE, SO_RCVBUF, SO_SNDBUF, TCP_NODELAY: optional socket options. WSAEHOSTDOWN (10064) Host is down.

after the first failed with WSAEWOULDBLOCK). The support for the specified socket type does not exist in this address family. If you are using a name server(s), check whether the server host(s) are up (e.g. We appreciate your feedback.

Although the specification doesn't list an error for a function, it does allow for it. This error apparently also takes the place of WSAEPFNOSUPPORT (which means 'protocol family not supported'), since that error is not listed for socket. For example, the error can occur when an attempt is made to read from a file that is not open, to open an existing read-only file for writing, or to open To get around the blocking issue, either put the socket into non-blocking mode, or use select() with a timeout to know when it is safe to call recvfrom() without blocking, or

WinSock functions: send(), sendto(), setsockopt() Additional functions: Any function that does network I/O: recv(), recvfrom(), FD_READ, FD_WRITE See also: WSAECONNABORTED, WSAECONNRESET, WSAETIMEDOUT WSAENETUNREACH (10051) Network is unreachable. Can this dress change colour dynamically? The requested protocol has not been configured into the system, or no implementation for it exists. WSA_QOS_EPROVSPECBUF 11018 Invalid QoS provider buffer.

It's also possible that the local services file has an incorrect port number (although it's unlikely). Recv and Recvfrom: If the datagram you read is larger than the buffer you supplied, then Winsock truncates the datagram (i.e.