WSA_QOS_NO_RECEIVERS 11008 QoS no receivers. WSAEDQUOT 10069 Disc quota exceeded. A service provider returned a bogus procedure table to Ws2_32.dll. WSA_QOS_EFLOWSPEC 11017 QoS flowspec error. http://devstude.net/socket-error/wsa-error-code-183.php
WSA_QOS_ADMISSION_FAILURE 11010 QoS admission error. The v1.1 specification also lists connect(), although it does not allocate a descriptor. In some instances, it also refers to the current state of the socket—for instance, calling accept on a socket that is not listening. No such host is known.
WSASYSNOTREADY 10091 Network subsystem is unavailable. Check whether you have a router configured in your network system (your WinSock implementation). Note the British spelling (with an 'S' instead of a 'Z'). A message sent on a datagram socket was larger than the internal message buffer or some other network limit, or the buffer used to receive a datagram was smaller than the
WSAECONNRESET 10054 Connection reset by peer. Check that your network system (WinSock implementation) has a utility that shows network statistics. Additional functions: With a datagram socket: send() or sendto(), or FD_READ. Socket Error 11004 This error occurs if you specifically reference a protocol that isn't part of the address family you also reference.
What is an instant of time? User suggestions: Did you enter a destination hostname? WinSock description: The Windows Sockets definition of this error is very different from Berkeley. It could also occur if an application opens and closes sockets often, but doesn't properly close the sockets (so it leaves them open, as "orphans").
If the hostname resolution uses a local host table, it's possible you resolved to an obsolete address. Socket Error 10061 Connection Refused Check the destination address you are using. The ICMP message means that the router can't forward the IP datagram, possibly because it didn't get a response to the ARP request (which might mean the destination host is down). A Windows Sockets implementation may have a limit on the number of applications that can use it simultaneously.
recv(), recvfrom(), send(), sendto(): MSG_OOB was specified, but the socket is not of type SOCK_STREAM Developer suggestions: don't do that. closesocket(): occurs on a non-blocking socket with non-zero timeout set with setsockopt() SO_LINGER. What Is A Socket Error Berkeley description: A socket operation was attempted to an unreachable host. Socket Error Codes Linux Is it poor technique or physiology that causes people to cycle with their knees sticking out to the side?
WSATRY_AGAIN 11002 Nonauthoritative host not found. http://devstude.net/socket-error/wsa-error-code.php Do you have a router configured? Alternately, you could call setsockopt(SO_REUSEADDR) to allow duplicate local addresses in a single application, but this is a kludgy approach (i.e. WSA_QOS_RECEIVERS 11005 QoS receivers. Socket Error 10054 Connection Reset By Peer
If it persists, exit Windows or reboot your machine to remedy the problem. a TCP reset received from remote host). Note that this error is returned by the operating system, so the error number may change in future releases of Windows. check my blog try to ping the server(s)).
Berkeley description: An asynchronous signal (such as SIGINTor SIGQUIT) was caught by the process during the execution of an interruptible function. Socket Error 11001 User suggestions: Check that the WINSOCK.DLL file is in the current path Check that the WINSOCK.DLL file is from the same vendor as your underlying protocol stack. The requested service provider is invalid.
WinSock description: Partly the same as Berkeley. This is a generic error code, returned under various conditions. It would also timeout if a (FIN)ish TCP packet is not ACK'd (and even if the FIN is ACK'd, it will eventually timeout if a FIN is not returned). news Notice that asynchronous service and protocols functions are listed below, in addition to the hostname resolution functions.
A connection attempt failed because the connected party did not properly respond after a period of time, or the established connection failed because the connected host has failed to respond. If there is more than one Winsock DLL on your system, be sure the first one in the path is appropriate for the network subsystem currently loaded. If so, is there an older DLL in a directory in the path ahead of the directory containing the newer DLL? For instance, you might get WSAEBADF in place of WSAENOTSOCK on a system that provides some socket and file handle equivalency.
send() & sendto(): socket not bound (for Dgram) or not yet connected (for Stream) The v1.1 specification also has a detailed description for the connect() function which says: "socket not already WSAEMSGSIZE (10040) Message too long. WinSock functions:
For information on how to handle error codes when porting socket applications to Winsock, see Error Codes - errno, h_errno and WSAGetLastError.