Home > Socket Error > Wsa Error Code 10038

Wsa Error Code 10038

Contents

Ping the remote host you were connected to. See WSAENETUNREACH. You are calling both WSAStartup() and socket() inside of the ClientSocket constructor (which is not the best place for either of those calls). Update - As per Ben's solution, I am now using: void ServerSocket::accept(ClientSocket& sock);, and implementing as: ClientSocket mysock; server.accept(mysock); Thank you so much!!! have a peek at these guys

WSAEHOSTUNREACH 10065 No route to host. WinSock functions: Additional functions: any function that takes a socket (or file handle) as an input parameter See also: WSAENOTSOCK WSAECONNABORTED (10053) Software caused connection abort. Berkeley description: A connection was forcibly closed by a peer. How to deal with colleague that starts arguments?

Socket Error Codes Linux

WinSock functions: send(), sendto(), setsockopt() Additional functions: Any function that does network I/O: recv(), recvfrom(), FD_READ, FD_WRITE See also: WSAECONNABORTED, WSAECONNRESET, WSAETIMEDOUT WSAENETUNREACH (10051) Network is unreachable. Like this:if(numclients > 0){ for(int o = 0; o 0Likes Like Posted 11 August 2009 - 08:21 You can verify that the remote system is rejecting your connection attempt by checking the network statistics locally.

WSA_QOS_NO_SENDERS 11007 No QoS senders. Too many links were encountered in translating a pathname. WinSock description: Similar to Berkeley. Socket Error 11004 Do a traceroute to try to determine where the failure occurs along the route between your host and the destination host.

from windows it's // set to 'WSAECONNREFUSED', but from linux it's set to 'ECONNREFUSED' throw SocketException("Connection refused on recover."); break; case DENOTCONN: throw SocketException("Not connected."); break; case DECONNABORTED: throw SocketException("Software caused Socket Error 10053 WinSock description: Similar to Berkeley. This is usually a temporary error during host name resolution and means that the local server did not receive a response from an authoritative server. WSAEDISCON 10101 Graceful shutdown in progress.

WSAEMSGSIZE 10040 Message too long. Winsock Error 10054 Fix Do not set non-zero timeout on non-blocking sockets to avoid this ambiguity (see Chapter 9 for more information). WSAETOOMANYREFS 10059 Too many references. WinSock description: Same as Berkeley, and then some.

Socket Error 10053

On the server end, you could use a network system utility similar to BSD's "netstat -a" command to check that your server is running, and listening on the right port number. Yes No Additional feedback? 1500 characters remaining Submit Skip this Thank you! Socket Error Codes Linux Although most of this appendix is for application developers, the User suggestions contain information that end-users and application support personnel might also find useful when an application fails. Socket Error 10049 The ICMP message means that a router can't forward the IP datagram, possibly because it didn't get a response to the ARP request (which might mean the destination host is down).

WinSock functions: the list of functions that explicitly list this error in the v1.1 Windows Sockets specification. More about the author Every request(GET,POST) kicks off a new thread.S[cur] is defined as SOCKET s[100]. You may have to register or Login before you can post: click the register link above to proceed. The error occurs with the socket() function, which takes the socket type (protocol) and address family as input parameters. Socket Error 10054 Connection Reset By Peer

Microsoft C description: Permission denied. For example, the error can occur when an attempt is made to read from a file that is not open, to open an existing read-only file for writing, or to open Alternately, you could call setsockopt(SO_REUSEADDR) to allow duplicate local addresses in a single application, but this is a kludgy approach (i.e. check my blog Detailed description: There's at least one WinSock implementation that will occasionally fail a function and report this as the error value, even though the function succeeded.

Error Description List (0) No error WSABASEERR (10000) No error Berkeley Description: no equivalent. Socket Error 10061 Connection Refused NOTE: The MAKEWORD macro referenced in the code fragment is not available in the WINSOCK.H header file or in any standard header files. WSAEINVALIDPROVIDER 10105 Service provider is invalid.

Apparently, the Windows Sockets specification left this out by oversight.

WSAEBADF 10009 File handle is not valid. Most of the text comes from the output from the "man errno" command on Unix. string ClientSocket::recv(int bufsize) { if (!isConnected()) throw SocketException("Not connected."); cout << "SocketRecv: " << (sockfd == INVALID_SOCKET) << " " << sockfd << endl; vector buffer(bufsize+1, 0); cout << "SocketRecv1: " Socket Error 11001 Reply to quoted postsClear » Forums » Home » Forums » The Technical Side » Multiplayer and Network Programming English (USA) English (USA) English (USA) (COPY) Mark Community Read Forums

sinServer.sin_port = htons(PORT); // Port if(bind(server, (LPSOCKADDR)&sinServer, sizeof(sinServer)) == SOCKET_ERROR){ easymsg("Couldn't bind."); } int numclients = 0; socketinfo clients[9]; for(int uu = 0; uu<9; uu++){ clients[uu].isused = false; } if(listen(server,9)){ easymsg("Listen See also: WSANO_DATA, WSANO_RECOVERY, WSATRY_AGAIN WSANOTINITIALISED (10093) Successful WSAStartup() not yet performed Berkeley description: No equivalent. All rights reserved. news WinSock functions: bind(), connect(), sendto(), socket(), FD_CONNECT See also: WSAEPROTOTYPE WSAEALREADY (10037) Operation already in progress.

Privacy Policy | Legal | Steam Subscriber Agreement | Refunds STORE Featured Explore Curators Wishlist News Stats COMMUNITY Home Discussions Workshop Greenlight Market Broadcasts ABOUT SUPPORT Install Steam login | language As you can see from the comprehensive list of WinSock functions, this error is the catch-all. WinSock description: Same as Berkeley. Developer suggestions: WSAStartup() failed, and you didn't detect it, or it wasn't called for the current task at all, or you called WSACleanup() too many times.