Home > Error Codes > X642e Error Codes

X642e Error Codes

Contents

POR several times Check each board for secure ground. When the last screen displays, the original message displays. Additional sub error codes display if you press and hold Start ( ) and 2 when an error message is displayed. It may be necessary to remove the re drive assembly to observe the lamp cycling on and off. news

What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account? Replace the assys in the following order 1. Service error codes are indicated by a three-digit error code followed by a period and additional numbers in the format XXX.YY. To display sub error codes (where available) When a 9xx or 2xx error displays: 1.

Lexmark Error Codes

Reconnect. Error 52 Flash Full - Not enough flash memory for data requested to be stored. Check connecting cables for continuity. May be due to the paper feeding manually while motors running and previous page in path.

Error 24X Paper Jam - Check Tray "X" Primary: Paper is jammed around Tray X (X=tray 1 thru 5). Diagnostic information 7002-xxx 2-115. 2-116. 4-48. "848.00 2-13 Previous page Next page 1...474849505152535455 Also See for Lexmark X642e Lexmark X644e User Manual 191 pages Lexmark X642E Quick Reference 5 pages Check to see if a modem card is installed in the MFP. Lexmark Ms310dn Error Codes The thermistor provides feedback on the temperature of the fuser roller and when it fails, the fuser power is shut off and the fuser does not heat up.

Check for correct installation of the motor driver card to flatbed interconnect card cable. Lexmark Fax Error Codes If no modem is installed, install a modem card. Check the toner metering cam on back of suspect cartridge. Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers

Continue pressing Start and 2 until each screen of information is obtained. 3. Lexmark Scan To Email Error Codes Sub error codes for 8xx, 9xx, and 2xx error codes The sub error codes are helpful troubleshooting a paper path problem, especially paper jams in the printer, envelope feeder, and duplex In most cases, five digits are shown. If correct, replace the following FRUs in the order shown: • ADF CCD cable. • Flatbed interconnect card.

Lexmark Fax Error Codes

It may also indicate interference between the flatbed CCD assembly and a metal bracket. Additional info on X and XX codes available by email. Lexmark Error Codes Also, can I get some instructions on putting in the rollers. Lexmark Printer Error Messages This error indicates that a problems has been detected with the flatbed carriage mechanical hardware.

Error 923 Fuser is too hot while printing or when idle. • Short in the thermistor circuit. • Noisy thermistor signal • Fuser is actually overheating due to hardware faults. navigate to this website Replace with the correct printhead. If you are on a personal connection, like at home, you can run an anti-virus scan on your device to make sure it is not infected with malware. Can be system board or printhead. Lexmark Error Codes Problem

Check the operation of the toner sensor. The main motor assembly may need to be replaced. Don't show me this message again. More about the author I truly appreciate it.

Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. Lexmark Engine Error CloudFlare Ray ID: 2fbfe69e50e05432 • Your IP: 204.152.201.107 • Performance & security by CloudFlare ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve If the test fails, the disk is defective or the data on track1 is bad.

I am new to this and do not want to screw this up.

Reload the paper and do a power on reset. FRU 1 MDC cable 842.xx Error code service check Service Scanner—scanner communications failure. Error 63 Unformatted or Defective Disk The printer will ignore a disk it senses as defective. Lexmark Support Remove jammed media How did we do?

Verify latch relay is operating - slowly close door and listen for interlock switch 3. Check connections to the to interconnect card assembly. I will have purchasing call in an order. click site Controller Board 2.

The system returned: (22) Invalid argument The remote host or network may be down. Replace Printhead Pricing Error 935 Printhead Error - May have sub-codes. Error 82 Photo Developer Cartridge Exhausted The Photo Develper (OPC belt cartridge) has reached the end of it's life and must be replaced. Don't show me this message again.

Fuser errors can be from a cold fuser or an overheated fuser. Make sure there is no paper jammed in the printer. Check printhead, cable, motor, system board. Open doors and covers and remove the toner cartridge.

It may take the printer 10-20 seconds to determine if the print cartridge is defective. Can also be LVPS or system board. Error 54 Serial Error - Framing or parity error on serial. Los Altos Hills, CA Thank you.

Request Quote Error 920 920 Fuser Error indicates the Fuser is below temperature while printing. All rights reserved. If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed. Replace Printhead Pricing Error 936 Error 937 Error 936/937 Main Drive Motor, Transport Motor An error with the main drive motor has been sensed by the printer Optra s 2450 Optra

Service error codes (8xx.xx) Error code 842 843 Sub codes .xx .xx Display text Service Scanner Service Scanner Description This error indicates that a scanner communications failure. Indicates that the fuser is below standby temperature when the printer is idle. My Account| Cart| Order Status Market Point Search: select Advanced search Read Customer Reviews GSA Contract Schedule Enter Here Need Assistance?