Home > Error Codes > X25 Error Codes

X25 Error Codes

Contents

X.25 sets the L3WINDOW to X if its original value is too big. CU%...is displayed instead of CU%ccu when the device supports extended I/O addressing or when the system is a multiple-channel system; that is, it can support more than one channel per processor. RecoverySee the recovery actions described in Table133-3. F0 A4 Dictionaries exhausted: impossible to activate a compressed logical channel. news

Often, a diagnostic gives only a general clue as to the source of a problem. F0 A1 Sessions on the destination port exhausted. F0 CF Obsolete. Codes in the second category (hexadecimal code 01 through 29) indicate problems between the PSDN and the remote host.

Hp Fax Communication Error 37

F0 A9 Call collision in one session F0 AA Compression protocol not compatible. If only message 74 appears, this is just a warning. A non-zero call-clearing code indicates the call-clearing request originated in the PSDN. Please give us some time and try again later.

F0 D5 SDLC: the PU being addressed is not configured or does not exist. When the extended format of the message is used, (cpu,chan,%ctlr,%unit) is displayed at the end of the message.#errnumidentifies a file-system error.CauseAn I/O bus error occurred during a transfer. When the extended format of the message is used, (cpu,chan,%ctlr,%unit) is displayed at the end of the message.CauseThe operator successfully brought up X25 through the Peripheral Utility Program (PUP) UP command.The See Table123-8 for I/O error codes returned for %param1.

The circuit cannot be used.If the logical circuit is a switched virtual circuit (SVC), the call is cleared.Other logical circuits on the line are not affected.In cases of multiple circuits, all Comm Error See Table133-7 for error codes.%param1contains the A and C frames.%param2contains the T and S frames.CauseAn invalid frame was received. F0 A7 X25: the destination port is out of service (OSI LEVEL 3). Level 2 is functioning properly, but level 3 is not.In cases of multiple circuits, this message may indicate that the link is down.

CU%...is displayed instead of CU%ccu when the device supports extended I/O addressing or when the system is a multiple-channel system; that is, it can support more than one channel per processor. F0 B0 Value assigned at the system startup. NoteThese diagnostic codes can be produced by any equipment handling a given virtual circuit, and are then propagated through all equipment handling that virtual circuit. Bios Central is a trademark of Bob Hurt.

Comm Error

If you know of any error codes that I am displaying incorrectly or that aren't here. F0 AC SVC: unexpected internal code. Hp Fax Communication Error 37 Please try the request again. Fax Error Codes One or more parameter settings that you made in x25tool are unacceptable to the PSDN.

I have a problem with my account. http://devstude.net/error-codes/wsasend-error-codes.php If val is less than 95, there are many retransmissions of frames on the specified line; that is, the line is noisy.CauseX25 reported a change in the line quality. F0 C7 An internal error caused the compression module to be reinitialised F0 C8 Internal code not provided for the commands SEND/RECEIVE. Level 2 is functioning properly, but level 3 is not.EffectThe line remains in state R2 or R3.RecoveryIssue either the Subsystem Control Facility (SCF) STOP LINE and START LINE commands (on G-series Epic

F0 92 IP Router: closure caused by an INIT command of the IP port. Table A-1 describes the differences between our implementation of certain X.25 network-generated, "international problem" diagnostic fields and the definitions provided in Annex E of "ITU-T Recommendation X.25." The Annex E Table F0 C5 Obsolete. More about the author Table C-3 CONS Diagnostic Codes Hexadecimal Code Decimal Code Meaning Sent by CONS E0 224 Unspecified E1 225 Disconnect--transient E2 226 Disconnect--permanent E3 227 Reject--transient E4 228 Reject--permanent E5 229 QOS

Thus, receipt of a diagnostic code may not indicate a problem with the router. If the line is down, bring up the line using the SCF START command.%1715The driver fails to get the I/O.X25 freezes.Contact your support representative.%2117The X25 primary process detected that the backup F0 CE Obsolete.

Additional information to help in troubleshooting can be found in the Event Management Service (EMS) log for message 74.

Internal disconnection codes which are not caused by errors in the X.25 procedure, have FO as the cause (see also the parameter MCAU in the port parameters) and the appropriate value Codes in the fourth category (hexadecimal codes 05 through 15) indicate problems within the PSDN. F0 E2 Obsolete. In such cases, all of the logical circuits on the line are affected and the application itself may not be involved in the error.EffectThe logical circuit is placed in an out-of-order

CU%...is displayed instead of CU%ccu when the device supports extended I/O addressing or when the system is a multiple-channel system; that is, it can support more than one channel per processor. Your cache administrator is webmaster. F0 96 TELNET: sessions of the TCP port exhausted. click site Typical values and their meanings are as follows: 1Received a DATA packet with an invalid packet sequence (PS).2Received an RR, RNR, or DATA packet with an invalid PR.39Received a DATA packet

For more detailed information including recovery actions, see the Guardian Procedure Errors and Messages Manual. F0 D1 SDLC, HDLCT: ;the received frame is too long (greater than N1) F0 D2 Obsolete F0 D3 SDLC/QLLC: ;received a too long sequence of X25 packets with M-bit= 1 (greater If the assignments are incorrect, change the assignments; otherwise, check the remote system.226X25AM: LCN #lchan OPERATIONAL CauseA problem reported by X25 message 224 or 225 has been solved.EffectNone.RecoveryInformational message only; no F1 A3 Simulator: closure due to an error noted in the comparison between the frames sent and received.

If it cannot download the primary path, X25 attempts to download on another path.RecoveryDecode the status byte to determine which error occurred. I have feedback for Stan. The system returned: (22) Invalid argument The remote host or network may be down. Table 3.

This combination of messages tells you that: The problem was detected by the PSDN, not by the remote host. This error applies to all I/O processes.EffectThe operation is retried, then the other path is tried. F0 C3 Format of the compressed data not valid. You can think of the first part as the test code and the second part as the fault code.

If the line is still running, then this is just a warning.