Home > Error Codes > X-ray Tube Error Codes

X-ray Tube Error Codes

Contents

Unit Calibration Required (If In The “CHECKSUM-BYPASS” Mode) 6. FIL/KVP Board May Be Defective 3. From Error 320 2. Re-Grease HV Xformer/XRT Wells 14. news

However, you probably have a defective xray tube. Bad Rotor Board 5. Soft Batteries/Cells 21. Bad Display/Display Controller (Newer Display Board 46-232832G1 Per Service Note 3611) 5.

Shimadzu Portable Error Codes

If Batteries Do Not Pass The Load Test, You Get To Replace Them!! AdvertiseIncrease YourBrand Awareness Auctions + Private SalesGet TheBest Price Buy Equipment/PartsFind TheLowest Price Daily NewsRead TheLatest News DirectoryBrowse AllDOTmed Users Ethics on DOTmedView OurEthics Program Gold Parts Vendor ProgramReceive PHRequests Gold Check Spark Gaps On H/V Xformer (0.010”) 3. Tune into our Clean Sweep Auction now to bid…600 Lots worth of equipment!

Check For Defective Jumper Harness From J3 On 1 KHZ Board To J7 On FIL/KVP Board 5. Batteries May Be Defective If Voltage Is Really Less Than 90 Volts 5. Open Filament In XRT (ERROR 45F) During Prep. SOLUTION: On Newer Style Base Assemblies, With The Newer Motor Mounting Assy. - Check For Drive Belt Tightness (The Motors Are NOT Spring-Loaded; They Are Tightened Down After The Proper Belt

Bad Main SCR(s) Q1 Or Q2 22. ERROR 462 During Cal. Bad Rotor Board 2. AMX1A4C6 Bad (FIL/KVP Bd.

Cell Readings Should Be Within .2 VDC Of Each Other (Ex. 11.9 vdc To 12.1 vdc). MA Appears High And KVP’s Low-Can’t Get The MA Down - Check To See That The Small Spot Is Boosting Rather Than The Large Spot (Filament Mis-wire In The XRT) 6. Defective FIL/KVP Board ERROR 437 1. Check For Correct Wiring Of TS2 On Rotor/Charger Panel AMX1A3 4.

  • Bad FIL/KVP Board 3.
  • The system returned: (22) Invalid argument The remote host or network may be down.
  • EnglishChinese (Simplified)FrenchPortugueseSpanishGerman Buy Sell About My DOTmed Login WE ARE LIVE NOW!
  • Display Issues—Trashy, Scrolling Or No Display During Charge.
  • Your cache administrator is webmaster.
  • NOTE: System Parameters Are Still “Looked At” In The “Check Sum By-pass” Mode. 8. -- Problem KVP Output Waveform Initial Rise 10-20 KVP High For 4-5 Msec. (During Calibration And Applications),
  • Batteries May Be Soft.
  • Replace LVLE (T3497L).

Shimadzu Error Codes

Error 462 On Exposures >70 KVP And Error 439 Closed Loop Resistance?) = Re-Calibrate Unit 8. If Error 320 Occurs After Error 321, There May Be A Temperature Problem On The 60 Hz Inverter ERROR 322 1. Shimadzu Portable Error Codes Check Wiring Of J4 Plug To FIL/KVP Board 5. Shimadzu Mobile Art Evolution Service Manual Check Tap Relay(s) [Contacts] 8.

EXP STOP CMND And SCR HI/LO Are Single Pulses 4. navigate to this website There May Be Oscillations Or Trash On The “XRAY ON” Signal (Could Be Bad Tap Relay Contact(s) 2. Is The XRT From Another Vendor? (Must Have Internal Resistor In Series With Filament) 7. Bad Front Casters 11. Shimadzu Mobile Art Plus Service Manual

Check Charger Board Feedback And Make Sure It Is Going Out To The CPU (TP-6 On The Charger Board) 3. Check For Correct Wiring Of BLK/WH/GRN Leads To Tube Stator From J4 Of Rotor Bd. 6. Copyright ©2001-2016 DOTmed.com, Inc. More about the author Check Pin Spread On Both Ends Of Cathode Cable (Also Check For Proper Amount Of Grease In High Voltage Cable Wells) 21.

Loose Leads On Service Toggle Switch (Not Going To Applications) 10. Side Cover Fish Paper Insulation Impacting Tap Relays When Cover Installed 8. Bad FIL/KVP BOARD (See Additional Notes #3) 7.

With NO Exposure Termination (Counts Actual Time)—In Check-Sum Bypass Mode, The Exposure Terminates Normally (Uses Time Selection ONLY).

Your cache administrator is webmaster. Scooter Log inor Register to rate and post a comment (331) (59) (13) Manuel Casanova Re: GE AMX 4 error code January 21, 2007 08:58 AMX - 4 / 4+ ERROR Check That All Contactors K1 Thru K6 On AMX1A4 Panel Pull In When PREP Is Pressed 2. Bad Handswitch 9.

Batteries May Be Soft - Refer To ERROR 465 - Could Be 1 Bad Cell Up To Full Pack 4. Check EXP STOP CMND Circuit On 1 KHZ Board. Please try the request again. click site Check For Miswired Plug At J4 On 1 KHZ Board 3.

Generated Thu, 03 Nov 2016 12:24:33 GMT by s_hp90 (squid/3.5.20) The system returned: (22) Invalid argument The remote host or network may be down. Insulate (On Older Units) Capacitor C5 From It’s Retaining Clamp (S/N 3265) 8. Bad CPU Board 9.

And 3. best regards Log inor Register to rate and post a comment (13) (2) Mario Mancha Re: GE AMX 4 error code January 19, 2007 11:30 Hi 465 current com feedback is Check Wires (push-On Terminals) To Both Fuse Holders (F1 & F2)--Pull Each One Off And On Once To Clean Terminals (Oxidation Issues) 5. To Handle Transducers Missing Or Low 7.

Check Ribbon Cable From 1 KHZ Board To CPU Board 2. Bad Tap Relay(s) 16. Bad CPU Board 11. ERROR 45D 1.

Voorbeeld weergeven » Wat mensen zeggen-Een recensie schrijvenWe hebben geen recensies gevonden op de gebruikelijke plaatsen.InhoudsopgaveIntroduction3 Students own department6 Pre test8 Routine maintenance modules11 Routine maintenance overview13 Maintenance survey for an Static Problems - Refer To ERROR 437, Step 4. 2.