Home > Error Codes > X 25 Error Codes

X 25 Error Codes

Contents

However, you can also receive this message if the maximum I-frame size is set to a size lower than the PSDN expects. F0 A6 The destination port is out of service (OSI LEVEL 2). F0 98 TCP: Retries exceeded. F0 CD Obsolete. check my blog

F1 A1 Simulator: closure caused by the receipt of a too long M-bit sequence. F0 AD PVC: unexpected internal code F0 AE Access password to the control port not valid. One or more parameter settings that you made in x25tool are unacceptable to the PSDN. Your cache administrator is webmaster.

Hp Fax Communication Error 37

Table C-2 X.25 Diagnostic Codes Hexadecimal Code Decimal Code Meaning 00 00 No additional information 01 01 Invalid P(S) (send-packet sequence number) 02 02 Invalid P(R) (receive-packet sequence number) 10-1F The system returned: (22) Invalid argument The remote host or network may be down. F0 CA Obsolete. Table C-3 CONS Diagnostic Codes Hexadecimal Code Decimal Code Meaning Sent by CONS E0 224 Unspecified E1 225 Disconnect--transient E2 226 Disconnect--permanent E3 227 Reject--transient E4 228 Reject--permanent E5 229 QOS

F0 B4 Impossible to carry out compression between two USER ports or two NETWORK ports. Use x25tool to modify your link configuration as necessary. In the routing there is a POO that either does not exist or could not be used in order to prevent an undesired call loopback. F0 B1 Obsolete.

For example, your call might be cleared with the code 00 42, indicating an invalid facility parameter setting. Internal disconnection codes which are not caused by errors in the X.25 procedure, have FO as the cause (see also the parameter MCAU in the port parameters) and the appropriate value F0 BE Obsolete. Copyright© 2011 Dialogic Corporation.

F0 A8 The destination port does not exist. F0 B5 Maximum number of attempts to connect with alternative routings, has been reached. F0 A9 Call collision in one session F0 AA Compression protocol not compatible. F0 DB SDLC/QLLC: the PU has received an invalid X.25/QLLC sequence.

  • Print this page Not Found The requested URL /ww_nt/admin/diags.htm was not found on this server.
  • F0 A2 Closure following a RESTART SYSTEM or the command C C PO:x SES.y.
  • The tables on the following pages specify the meanings for these numeric codes.
  • Generated Thu, 03 Nov 2016 20:12:20 GMT by s_fl369 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.8/ Connection
  • F0 DA SDLC: the primary PU has received an FRMR frame.

Comm Error

F0 97 TELNET: The fields received for address calling and address being called differ from the ones configured. F0 CE Obsolete. Hp Fax Communication Error 37 Generated Thu, 03 Nov 2016 20:12:20 GMT by s_fl369 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection Fax Error Codes F0 C6 HDLCT: disconnection as consequence of a ;RESET occurred between the two HDLCT ports.

F0 D8 SDLC: the primary PU, in an "ACTIVE" state, has exceeded frame retransmission attempts. http://devstude.net/error-codes/wsasend-error-codes.php F0 92 IP Router: closure caused by an INIT command of the IP port. You receive the remaining codes in Clear Request/Indication packets. F0 A0 No routing is satisfactory for the call. Epic

F0 A3 Cause and detection not available in the "CLEAR" or "RESET" packets received. Remember that any adjustment of the maximum I-frame size, a LAPB parameter, might also require a change to the default packet size parameter, at the X.25 Packet Layer. F0 D1 SDLC, HDLCT: ;the received frame is too long (greater than N1) F0 D2 Obsolete F0 D3 SDLC/QLLC: ;received a too long sequence of X25 packets with M-bit= 1 (greater news If you receive error code 00 42 and are not subscribing to any facilities, or are confident that your facilities parameters settings are correct, confirm that you and your PSDN agree

F0 D5 SDLC: the PU being addressed is not configured or does not exist. Documentation Home > Solstice X.25 9.2 Administration Guide > Appendix C Error Messages and Error Codes > Error CodesSolstice X.25 9.2 Administration GuidePrevious: Error MessagesNext: Appendix D Installing the Solstice Often, a diagnostic gives only a general clue as to the source of a problem.

Please try the request again.

However, in some instances the error code may indicate a configuration problem that you can correct yourself. Abilis CPX internal codes Cause( hex ) Diag.( hex ) Meaning F0 90 IP Router: no IP port has been recognized. ITU X.25 diagnostic codes Diag.( Hex ) Meaning 00 No additional information 01 P(S) not valid 02 P(R) not valid 10 INVALID packet 11 Type of packet not valid for rl Please try the request again.

F1 A5 Simulator: generic regular closure. F0 A7 X25: the destination port is out of service (OSI LEVEL 3). Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request. More about the author Legal Notice Error: Could not find file 'E:\Inetpub\wwwroot\new_support\training\control.mdb'. {{offlineMessage}} Store Store home Devices Microsoft Surface PCs & tablets Xbox Virtual reality Accessories Windows phone Software Office Windows Additional software Apps All