Home > Error Code > Wm2277hs Error Code Le

Wm2277hs Error Code Le


The dryer is on top and I am the only one here. The sensor is not covered for 7 years. I've since removed all sweaters and attempted to just run a hand wash cycle with nothing in the machine. Plug off the wall. this contact form

Discover LG OLED Close Appliances Skip to Next Menu Appliances LG Promotions Kitchen Appliances Refrigerators All Refrigerators French Door Side-by-Side Bottom Freezer Top Freezer Door-in-Door® Cooking Appliances All Cooking Appliances Ranges Thanks to all Dave September 2013 Have replaced sensor and worked for about a month. My quesition is...when mountd in the washer The two electrical posts on the pump motor, are they horrizontal to the bottom of the washer or are they vertical one on top The hall sensor solution seems to have resolved my LE issue also.

Lg Top Load Washer Le Error Code

The part number again is 6501KW2002A (hall sensor). This will rinse out the tub. I'll post again soon if the problem returns.

  1. Plug in the Washer 8.
  2. All the instructions are very useful, and hope my issue will also go away..
  3. Running as usual!
  4. Thanks!
  5. Any help would be greatly appreciated.
  6. Vinny from Toronto, Ontario.
  7. No thanks LG I found a local appliance shop who had the part in stock (same part number for my machine as the one listed in the original question), I replaced
  8. this process reset the sensor.

He said the motor was bad and needed replacing. Today, we unplugged the machine for 7 hours... Tabor March 2010 Thank you to everyone for your answers in this forum. Lg Washing Machine Error Code De I then soldered 4 wires that were about 3 inches to each of the pins (the center pin doesn't require a wire).

Single bulky items or large loads can add extra weight to the drum and place stress on the motor. Lg Washer Le Code Not Spinning Sign in Transcript Statistics 59,517 views 49 Like this video? I unplugged.

Melody March 2010 With the LE code.....be persistant but patient......I tried unplugging and plugging it right back in several times, turning it off and on, etc.....it didn't work.

i can not find it to get the part # in the manual, nor can I find where I can purchase it. Lg Washer Error Code Ue I finally got out my multi metere and started tracing the wiring out as the diagram says and found a clean break in the gray wire for the hull sensor. Click here for how to enter without purchasing or registering a product and Official Rules. Happy Mama July 2012 hall sensor; 6501KW2002A was the answer for my problem; thanks for these comments; Canadian shops wont sell the sensor!!!

Lg Washer Le Code Not Spinning

Todd from Arizona July 2010 Thanks Terrell this worked for us! ausphoche June 2011 Awesome! 4 spins each way and works like a charm - though wear a raincoat as I'm soaked from the water in the drum :) Laura June Lg Top Load Washer Le Error Code Thanks so much! Lg Washing Machine Error Code Ie I tried your "simple" and cheap fix first before I called for parts.

That worked for now. weblink Guest Don't usually participate in discussions. One speed wash done and another in washer now. None of it worked this time. Lg Washer Error Codes

TheNewReview 6,865 views 2:11 How to Fix an LG Front load washer machine that wont spin - Duration: 5:32. I put the strain back and plugged it again and valla! Skip to Contents Skip to Accessibility Help LG SIGNATURE Skip to Next Menu LG SIGNATURE LG SIGNATURE Brand Story LG SIGNATURE Products Products OLED TVs Refrigerators Washers Dryers Air Purifiers LG http://devstude.net/error-code/wmi-error-code-5.php After this--use the correct amount of "HE" detergent & perform a "TUB CLEAN" cycle every (4) months using the *tub clean* option on the control panel.

What I have had to do is to take all the wet clothes out of the dryer, dip the water in the dryer out. Le Error Code Lg Dishwasher With the old hall sensor, this led remained OFF. LE Error.

Click here for Tecumseh repair information.

Motor Sensor - LG/ Kenmore Washer This video provides step-by-step repair instructions for replacing the rotor position sensor (or motor sensor) on a LG/Kenmore f... but if you don't, you could get by with a pair of pliers or vice grips. HE liquid soap directions are followed with success. Lg Top Load Washer Error Codes Unplug the machine. 3.

The hall sensor may be defective but you will need a technician to check out the other things listed here. There is a black and a brown wire and we are unsure which post thest connect to. The LE code could indicate a number of possible issues. (bad HALL Sensor, clogged drain filter, bad bearings, bad stator, bad control board) All can be fixed by just about anyone his comment is here Model retention may be affected by your browser settings.

Sign in to report inappropriate content. Then the digital window flashes 'LE' and the machine starts to beep. it works fine! The LE code indicates a problem with the motor.

Anyone have this thing go away, come back and not go away again? You saved me $1000 for a new washer. Recently, it just won't go away. Answers Who answers the questions?

The machine is still used today. Void outside the U.S., in Puerto Rico, and wherever else prohibited by law. SJF12rn March 2011 FIXED. .... Click to Call Click to Chat Sears.com 1-800-491-3457 Login Register Order Status Feedback Recently Viewed Models Parts My Models (0) Cart Your Shopping Cart Checkout Now Showing last added item Parts

Unplug for 10 minutes (didn't work after just rotating) 4. This part is also called a hall sensor or motor sensor. details: Supplier in Canada: www.partsquick.ca Part was 6501KW2002A Price was $20 CDN Delivery overnight by land courier: $10 Time to install: 45 minutes Difficulty: LOW. Pull that back panel off of the washer to access that motor.I hope this helps.

I thought I was going to have to replace it, but I'm thankful I didn't because I can't afford one right now. I have replaced the HAL sensor at least 6 times - I can do it in about 12 minutes now! They correctly advised unplugging the machine for 30 minutes. 4 years later the LE error came on again. Lastly, a breakdown in the signal between the microprocessor and the motor may cause that error code.